Tuesday, February 23, 2010

Samsung I5700 (Galaxy SPICA) Android 2.1 Flashing Guide (Updated)


***** USE THIS GUIDE AT YOUR OWN RISK !  *******
***** DO NOT BLAME ME FOR BRICKED DEVICES ******


What you need : 

The firmware : I570EDDJB2 in my case. (Unreleased Android 2.1 (Eclair) firmware from Samsung).
Multiloader application and Spica OPS (Odin_v4_03.exe + spica.ops) : Odin_v4_03.zip
*** Please use the new spica_jc3.ops file for the firmwares I5700XXJBA, I570EXXJC3 I570EXXJC5
Drivers for I5700 : drv5700.zip
Samsung USB Cable

Before you start : 
Backup your data !
Remove the SIM lock if any.
Create a folder and extract all files listed above + the firmware (do not extract the tar file from within the firmware)
Ensure your phones battery is sufficiently charged (and your laptops battery too if you live in a country like ours lol ;-))
Shutdown any service/software which could be using the USB port, especially the Samsung PC suite. - Very Important

Flashing :

Edit : You should probably do a hard reset before you start by punching in the following code on the phone *2767*3855#

1. Shutdown your phone and remove the SDCARD and the SIM 


2. Put the phone in "Download Mode" by pressing Volume Down + Camera + Power button.
Image Courtesy : samdroid.net
3. Connect the Phone to the PC using USB
4. Install drivers using the drv5700 files- A lot of guys are going wrong here.  Open your device manager and ensure the two Samsung devices are shown properly before you go ahead.(circled in red) - see image below :


4a. Disconnect phone from the USB. *** (Very Important), thanks to Srikanth Kapa (For all you guys having problems with "Setup Connection"
5. Open Odin Multi Downloader v4.03.exe and then reconnect the phone, you should see the a COM port number with a yellow background.
6. Select the files as shown in the image below : 

Image Courtesy : samdroid.net
If you are using some other firmware and there is only one tar file select Option : One Package and load the file under One Package TAB.

Cross check the files and if you need to change anything click on "Reset Files" and select files again.

7. Once you are ready hit the START button. DO NOT DISCONNECT the phone until the firmware download completes.

8.Watch the "Message: window and wait till it shows <1> Close serial port and wait until rebooting.- This usually takes not more than 1-3 minutes.

9. At this point your flashing is complete and the device should be automatically rebooting, once the reboot is complete unplug the USB cable and flick open the Eclair green locking slider ;-)

Congrats !!! Welcome to the delicious ECLAIR club :-)

Issues : 

Google Maps seems to be a bit temperamental (Upgraded to ver 4.0.0 from the new 2.1 Market). Phone has hung a couple of times but nothing really serious.

New Features : 

Multiple Accounts Support
Exchange Support - No Calendar support or GAL lookup.
Camera now has Scene mode, White balance, Color effect
Search across the device including SMS/MMS
HTML5 Support in the browser.
Live Wallpapers
Refreshed UI


Hopefully Samsung will include pinch and zoom in the final release version :-)

Thanks to the guys at : 

Screen Shots : 


  

 
  
  
 

930 comments:

«Oldest   ‹Older   601 – 800 of 930   Newer›   Newest»
Unknown said...

@ sameer: yes i can see a com port (com5) i assume its coz i hv already installed usb drivers from sdk package
still waiting for ur reply whether should i proceed or no!

Unknown said...

and 1 more thing
i m seeing samsung mobile modem instead of samsung android modem and in usb i m seeing samsung composite usb device in short instead of this
http://4.bp.blogspot.com/_hboAAPcQdIU/S4YpRf2uWrI/AAAAAAAACUw/9CHS34IbIqw/s1600-h/Drivers.PNG
i m seeing this
http://img22.imageshack.us/img22/7696/sdsdsv.png

GREAKY said...

@ Siddesh - since you had installed the NPS the drivers are already there. You can go ahead and flash.. Good luck.

viky said...

Guys just flashed to latest firmware XXJD1, with this guide its piece of cake thanks everybody, will keep you posted about this new firmware.

The. Commenter said...

Sameer i had disabled background data download, it had reduced my problem almost 90%. as i am in marketing unable to go service center. anyway thanks for your reply.

Unknown said...

@sameer: i tried but it got stuck up at <1>setup connecting... no damage to existing os though!
is this problem related to drivers?

Unknown said...

I knw i m sounding complete noob here but shd i uninstall nps n follow ur steps??

Nimesh Abraham said...

@sameer
I am gonna flash my spica.Should i switch on USB debugging mode(applications/development/USB debugging) on phone before flashing.Bcoz if i switch on that mode,in device manager of my pc Samsung android USB Modem and Samsung Android USB Composite device is showing.Please guide.

GREAKY said...

@ Siddesh - you need to disable NPS not uninstall it. No other software should be trying to access the USB when you flash.

@ Nimesh - USB debbugging mode is not required to be turned on for flashing.

Unknown said...

u dint get me i disabled the nps then i disabled windows mobile service center too!! still i was stuck up at <1>setup connecting n was there for long time. just wanted to ensure the problem before proceeding!

Unknown said...

Hello Sameer.
i success upgrade to 2.1 using your guide.
but now, eveyrtime i turn off and on back the handphone, it look all seting is gone. it is just like hard reset.
any idea how to solve this?

Unknown said...

@ Viky,

Any update on XXJD1 firmware?? How is it working?
Have u faced any problem?
What size internal memory remain after upgrading to XXJD1?
Is there any performance degradation?

@Sameer,

I have upgraded to DDJB2 but unable to activate Live Wallpaper !!
How do I make it enable?

Regards,

Unknown said...

hi sameer,

my firmware version is i5700DDIK2
can i upgrade it to 2.1 with the download link that u have given i.e

Unknown said...

hi sameer

my firmware version is i5700DDIK2 , can i upgrade it to android 2.1 ??

Ritesh Gupta said...

Baron, check your internal memory, I am sure it shows up 0.00B.

Flash with the debug option again or another firmware. That should help.

Ritesh Gupta said...

Siddhesh,
1. NPS still keeps running soemtimes. Search for the process in task manager and kill it.
2. Check your drivers.

Baron - Check your internal memory. I guess it shows up as 0.00B. You have to reflash with debug option or use another firmware if thats the case.

HTH,
Ritesh

za3tar said...

Hi Sameer,

I need your help, I have samsung i5700 with Android 1.5, I try all the way to update it, but nothing happen,
I went to:
http://samsung-firmware.webs.com/WEBPROTECT-samsungandroidi5700.htm
and I download "I5700JPJC1" and I use odin last ver. but it is not working ... still the same ver.

could you please help me????

GREAKY said...

@ Nirav - Yes you can.

Sandor said...

Thank you very much for the clear instructions! My Spica is now happily running 2.1

To be honest: I do not feel the update is so good that it warrants all the effort some of the users are going through,
as Eclair seems to break things as much as it improves, unfortunately.

One of the things I wonder about; is there a method to use Live Wallpapers without having to buy a Home replacement app or rooting the phone?

Unknown said...

Hi Sameer,

I did upgrade my i5700 to 2.1, I have installed some live wall papers but its not getting active or i dont see any option to enable !!!

How do I enable these live wall paper?

Regards,

Riyaz

Luka said...

First of all, thank you for the guide.

Second, I recommend to everyone who's not managing to update, to turn off the anti-virus. That is how I finally managed to update to Eclair.

cyberdrone said...

Hi,

i really want to flash my spica, but I can t get the USB drivers to work, my pc just won't recognise my phone as you specify in the screenshot, and I us the drivers you specify in your manual. I'm using win XP professional, and I have tried it on differant pC's at home and I can't get them to work ..

smitz said...

the update didnt go very well for me.. managed to do it only after 10 times. end of it, the 2.1 did look great but lost network coz imei set to a string of zeroes.
sent it to samsung service, who sent it all over the world and finally returned the phone back to me after 20 days with the restored imei. they said the official 2.1 shud b available in bombay by the end of this week.
wondering why the imei set to zeroes though, if anyone can throw any light on that.
pls note that i was reckless when the update was failing, and in the odin had unclicked "protect ops", and clicked "debug only", just to see if that helps update.. :-)
AFAIK, the imei is written on a "write once" chip and assumed it to be indestructible. now am wiser without any addition to intelligence.. lol

smitz said...

the update didnt go very well for me.. managed to do it only after 10 times. end of it, the 2.1 did look great but lost network coz imei set to a string of zeroes.
sent it to samsung service, who sent it all over the world and finally returned the phone back to me after 20 days with the restored imei. they said the official 2.1 shud b available in bombay by the end of this week.
wondering why the imei set to zeroes though, if anyone can throw any light on that.
pls note that i was reckless when the update was failing, and in the odin had unclicked "protect ops", and clicked "debug only", just to see if that helps update.. :-)
AFAIK, the imei is written on a "write once" chip and assumed it to be indestructible. now am wiser without any addition to intelligence.. lol

Unknown said...

Hi,

Just heard from Samsung Customer Care in India that the Android 2.1 update is officially available now. We need to go to the Service center (with the original bill) where they'll update the OS. Plan to try it as soon as I get some free time from office.

Cheers!

Unknown said...

@aman thats a gud news.. i will try to get in touch Samsung Service Center in Guwahati .. Hope the upgrade is available PAN india

Unknown said...

@Suraj, i think the update should be available pan India.. though do make sure the service center you visit has the software engineers to do the upgrade..
i just had a harrowing time visiting one of the Samsung Service centers in Hyderabad where they said they couldn't do it, inspite of me having been directed there by Samsung Customer Care.. The Area Service Manager has offered to help me out by ensuring an engineer is available tomorrow to do the upgrade for me.. i'll need to leave the phone with them for 3-4 hrs.. hopefully, it'll all go well and I'll have an eclair tomorrow..
haven't had a chance to spend much time with Cupcake (just bought the phone last Fri) but will post if i find any obvious performance improvements/deterioration..

Ravi Teja J said...

@aman- which service centre at hyderabad? i tried customer care samsung and they just rejected any android update for the phone, may be even i can be at the service centre tomorrow(i' m from hyd too)

viky said...

@Riyaz sorry for the late response bro, I was too busy wid lovely eclair :), its great no bugs found till now, its runnig smooth. I am confused about battery life as usual usage(browsing(1 hr),social networking(less than 1/2 hr), talk time(1/2 hr),music 1hr, etc) lasts 1&1/2 half day(atmost), i did not tried other firmware so not sure its better or lesser.

Unknown said...

Hey i followed ur guide.. no issues.. now i am tasting eclair..thanks sameer

Unknown said...

Hi and thanks for the tutorial.
I'm from Romania and after 3 days I've managed to update to 2.1 :D
So first, if you are from Europe, the firmware posted here is not good (it's for Asia area). You must download the latest firmware from samsung-firmwares for Europe (they have a colour legend there) and that should work.
I didn't knew this at first, so I strugled and managed to install the firmware posted here only by checking the debug only and not addind the CSC file in Odin. It worked like charm only that the after it started everything moved like crap so I downloaded the latest from samsung-firmwares (2.1 update 1), installed it with Odin, without the debug only checked and with all the added(so with all the options) and now it works quite nice.
Thanks again for your post because it really helped me understand how things work :O

Dajana said...

hi!
I have done all the steps in a proper way,but I have a problem with the sixth step...
The device is not shown in my computer...
Could you please help me ?
I am going crazy,cuz I have bought the phone couple of days ago,and my bluetooth is not working...I cannot enter the calendar
So i REALLY need this update...

Dajana said...

hi!
I have done all the steps in a proper way,but I have a problem with the sixth step...
The device is not shown in my computer...
Could you please help me ?
I am going crazy,cuz I have bought the phone couple of days ago,and my bluetooth is not working...I cannot enter the calendar
So i REALLY need this update...

Unknown said...

@Ravi, i went to the Service Station in Kukatpally (near BJP office) where the software engineer was not available. The Service Center folks at Kukatpally asked me to go the service center in Ameerpet where it could possibly be done, though I'm not sure. When I escalated it to customer care, they got me through to the Area Service Manager who gave me two options.
1. I leave my phone at Kukatpally Service Center and he'll get a Sr. software engineer to visit the center and update my cell. I could collect it the next day.
2. I visit the Kukatpally Service Center again today after calling him up and leave the cell there for 3 hrs. He'll arrange a software engineer to come and install the update.
I've been held up with some office work today and haven't been able to follow-up. Plan to give him a call on Sat morning and get it done then.
I'd suggest you give a call to the customer care, ask them to route you to the mobile tech support team and check with them which Service Center you could go to. Do make sure they confirm that a software engineer will be available when u visit.

Prabu Yuvaraj said...

Hi Sameer,

I had asked couple of questions regarding firmware issues few weeks earlier.

I'm have the I570EDXJB3 firmware. Everything works good for except one little snag. When I connect the phone to a computer, there is Android modem or Samsung device in the device manager like it previously used to be. And I'm not able to transfer files since the card is not getting detected. Any idea?

Prabu

Racingbeast said...

Sameer, following your advice now i tried with XP also but the same result. not able to flash it :-(

Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...

then no response

Ritesh Gupta said...

@Aman, Ravi
Wow! So much pain for the update. I am better off with Sameer's guide then. And ofcourse I've tried a lot more stuff with some inputs I got here. Having flashed my phone about 10 times now to try out different stuff and having rooted it, I guess its weird that Samsung wants you to give up the phone for 3-4 hours!

Cyrus said...

Hello,

I just bought my samsung i5700 with I5700DAJA1 firmware. I want to reflash it with the new firmware I570EDXJC4 . I am not sure if it will be working fine in Windows 7 as my operating system. I experienced problems in installing the phone drivers as what you mentioned here and odin.

What operating system you are using? The Pc Suite of samsung could not install the drivers you said even I have to update the unknown driver as shown in the Driver Manager.

I want to see the Android 2.1 running in my phone.

Waiting for your reply. Thanks. By the way, it will be my first time flashing.

And I think it's easy to flash the firmware.

Cyrus said...

Hi Sameer,

Can you do the new firmware posted in the samsung-firmwares?

I570EDXJC4 (2010 March)

Have you tried it? I wish to hear from you. I want to flash my phone with this but the file structure when I unzip is different from the one here.

Thanks.

Ritesh Gupta said...

Cyrus,
1. I used Windows 7 without issues.
2. The structure may be different for files when you use SINGLE file flash like JC4 you are trying.

I wrote down the whole test with that file (and issues with that file) on my tests section:
http://grittalk.blogspot.com

That might help you because we share exactly the same environment I guess :-).

Den Puri said...

Thanks....it works, after 20 times :D, the problem is the cache (CSC)...after i leave it blank...flashing success

Cyrus said...

Hi Retish,

I read your blog and I posted comments there. I hope you can reply.

Im now in doubt in flashing unofficial release. Maybe, the best way is to stock in 1.5

Thanks.

Cyrus

Ritesh Gupta said...

Wokay Cyrus, I replied you there as well just to be sure where you look. Some of the stuff on 1.5 makes up with 2.1 to certain extent. However, the 2.1 is real cool + having the satisfaction to flash your own phone is even more fun!

There is more fun stuff to do. You can try rooting, live wall papers ...

Well ... not always, but sometimes its fun to be one step ahead of contemporary stuff :-)

Unknown said...

Hi All,

For all those who want to upgrade to 2.1, simply follow the guide by Sameer, all goes very smooth and no problem at all as I too upgraded with same guide and my upgrade completed in just 1.30mins to copy file and rest all in 3mins.

If any one getting stuck at CONNECTION.. then they should try to remove battery, reinsert and start process again, all works fine.

Unknown said...
This comment has been removed by a blog administrator.
Unknown said...
This comment has been removed by a blog administrator.
Unknown said...

Hi Sameer,

I sucessfully upgraded to 2.1 with your guide, thanks for your guide.

When I am installing any Application or Utility it is getting install in Phones internal memory, where as I have big external memory installed and my external memory is not getting use... any idea why is it happening so..??? why installation is not using external memory ??

Regards,

Unknown said...
This comment has been removed by a blog administrator.
Ritesh Gupta said...

Riyaz - That is a restriction from Android. So you either need to root your phone or get su + remount on your phone. Then after modifying a couple of files, your phone can start saving applications on external memory.

Cheers!

Anonymous said...

HEY SAMEER . I TOO AM FROM INDIA . WHEN I TRIED FLASHING THE PROCESS WAS STOPPED AT COONECTION 1... AFTER THAT NOTHING HAPPENED .. WHAT CAN WE POSSIBLY DO .. THE PHONE IS NOT BRICKED AS I REMOVED THE BATTERY BEFORE REOVING THE USB PORT ...

Unknown said...

@ Bishal,

You need to check if your USB driver are installed properly and you can see the same in Device Manager window...

If the pricess is stopping at CONNECTION 1 window means it cannot find your mobile as a serial device to start trasnfering required software.

Regards,

Riyaz

Unknown said...

@ Bishal,

You need to check if your USB driver are installed properly and you can see the same in Device Manager window...

If the pricess is stopping at CONNECTION 1 window means it cannot find your mobile as a serial device to start trasnfering required software.

Regards,

Riyaz

Unknown said...

Hi All,

The guide by Sameer is very simple and works fine if you follows the steps carefully and one by one.

I have tried the guide with i570EDDJB2 Using old spica.ops file,
i570EXXJD1, i570EXXJD4 & i570EDXJC4 using new spica.ops file and all worked fine for me in just 3mins.

If any one getting stuck at CONNNECTION 1...
Disconnect mobile from PC,
Remove Battery from mobile,
Reboot your PC,
Put mobile again in download mode,
Connect mobile again to PC and start again.

Feel free to write back.

Regards,

Riyaz

Unknown said...

Hi All,

The guide by Sameer is very simple and works fine if you follows the steps carefully and one by one.

I have tried the guide with i570EDDJB2 Using old spica.ops file,
i570EXXJD1, i570EXXJD4 & i570EDXJC4 using new spica.ops file and all worked fine for me in just 3mins.

If any one getting stuck at CONNNECTION 1...
Disconnect mobile from PC,
Remove Battery from mobile,
Reboot your PC,
Put mobile again in download mode,
Connect mobile again to PC and start again.

Feel free to write back.

Regards,

Riyaz

Unknown said...

Hi Sameer, I was wondering if there is a chance to flash my phone without having to unlock sim. Also is some1 who tried that and it worked?

Ravi Teja J said...

@sameer -there are so many firmwares out nowlike jce jcf jd1 jd4..have u tried any new ones lately?
has anyone updated to 2.1 through new pc suite??

GREAKY said...

@ Stroe - do you mean the SIM lock or the phone is locked to a network ?

@ Ravi - I have been using XXJCB till now.. BTW as some of the people have reported here.. the official update is now available. Get in touch with the local service center and they should be able to update your phone.

GREAKY said...

Sorry guys I haven't been able to keep up with the comments lately.. I see a lot of people replying to each other though :) Lets keep up the good work. If there is anything that I have missed answering.. just let me know... Thanks all for the collective effort.

Unknown said...

Okey, Sameer. Now iam confused. Isn't Simlock the same with a phone locked to a network? I mean about what u wrote in your guide:"Remove the SIM lock if any.". My question was if I can flash the phone without that step.(I cant afford to pay right now for unlocking the network). I was wondering if someone flashed withour removind the sim lock? If so,pls replay back. Also, if no one did that, what are the risks?

GREAKY said...

@ Stroe - no SIM lock is a simple lock that anybody can enable by going into settings > security. I am not too sure about network locked phones.. maybe if somebody else has tried it .. they can reply.

Unknown said...

So, It is a must to unlock the phone from a network? I mean, if my phone is locked to a network, I can still flash it without having problems?

GREAKY said...

@ Stroe - I won't recommend that. you should check with somebody who has done it earlier. Most of the guys here have had unlocked phones.

Unknown said...

Thank you for your time. Iam gonna continue to gather infos until iam sure I can flash it without having any major risks.

Unknown said...

Hi Sameer,

I sucessfully upgraded to 2.1 with your guide, thanks for your guide.

When I am installing any Application or Utility it is getting install in Phones internal memory, where as I have big external memory installed and my external memory is not getting use... any idea why is it happening so..??? why installation is not using external memory ??

Regards,

Riyaz

Unknown said...

Hi Sameer,

I sucessfully upgraded to 2.1 with your guide, thanks for your guide.

When I am installing any Application or Utility it is getting install in Phones internal memory, where as I have big external memory installed and my external memory is not getting use... any idea why is it happening so..??? why installation is not using external memory ??

Regards,

Riyaz

Chris said...

hi im chris from uk i tried several times it says cant open usb serial port code 87

Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 87

Chris said...

hi im chris from uk i tried on 2 pc's and get the same error

Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 87

hope u can help

Unknown said...

I've read all 660+ posts in here, and I've not seen if anyone on Rogers in Canada has had any issues after updating. Also I've tried a few times using Vista, and I've not been able to complete......Is there something I'm missing?

GREAKY said...

@ riyaz - android does not use the SDcard memory for installing the apps by default. You will have to MOD using Apps2SD .. a comment just above yours has posted the link for the same..

@ Chris - Looks like the drivers are not installed properly.

@ John - As far I understand ODIN only works well with WinXP, some users have reported using Vista and the compatibility mode.

GREAKY said...

@ Riyaz - here is the link.. I am going to try this myself very soon.

http://forum.samdroid.net/threads/624-Spica-v.LK2.02-Root-Recovery-Apps2SD-Busybox-Wifi-tether-etc-04-15-2010-EN

Chris said...

it just keeps saying unable to conect to usb code 87

Anonymous said...

no @CRIS
i got struk at <1> connection
i too had faced proble same as urs then u ...try removing the usb cable and then inserting again but this shou;d be done after the odin is opened abut before u hit on the start button ...the yelllow background if present u wont face problem .. best way to check is thrugh device manger if ur device is shown in device manager>modems>samsung momdem or android modem

Anonymous said...

TRY THIS SITE DUDE
www.samsung-firmwares.com

it has every thing as tutorial like firmware flashind /firmware programing and all .all must check this site

Chris said...

how do i rectyfy this i have wiped my pc and put windows 7 on it still no luck

Chris said...

its yellow com 5 stull fals

ravisghosh said...

Hi Sameer:

I tried flashing 2.1 to i5700 and it was successful. But internal memory showed up as 0.00 B :(

Then following the clues given by you, I tried to flash 2.1 again with "debug only" selected. Now, I am not able to hard reset using *2767*3855# as every time I do it, it ends in a triangle surrounded by exclamation mark.

Tried going ahead without hard reset, but now the drivers are not being installed. I had NPC when I installed for the first time and the devices were recognized as Samsung USB Composite Device and Samsung USB Modem and the devices were recognized. But now, the second time, modem is not recognized properly, either it is not recognized at all or it shows up as SAMSUNG CDMA Modem #2. I try updating the drivers with the drv5700, but it fails as timeout period expires.

Any insight on it?

ravisghosh said...

Finally, I was able to get both the drivers as Samsung USB Composite Device and Samsung USB Modem in Device Manager, but now Odin got stuck at <1> Setup connection.

:(

Chris said...

still no luck got this phone form a site and its french sim free just put the language to english ukbase band version is i5700xxIL1 kerne; version 2.6.27 root"dell1-desctop) build version cupcake.xxil4 i only got this phone because of 2.1 i phones samung and they said its becase of only on 3 t-mobile and THEY COSTOM THE FIRMWARE. please if anyone could help be really gratefull

Chris said...

mate thank you for all your help i turned off my anti virus and used a newer firmware and it worked after 12 times trying your the best lol cheers again

ravisghosh said...

Here is something that worked for me.
1. Installed NPC 1.4 which would install drivers. Fact of note is that if you connect i5700 switched on, the drivers are recognized as Samsung Android USB Modem, etc. But if you connect in Downloading Mode, it shows up as Samsung USB Modem.

2. Needed to do multiple restarts of phone as well as windows vista to get the drivers detected properly. Often, the modem driver was detected as Samsung CDMA Modem #2 which would not work.

3. I was not able to hard reset the phone as explained earlier, so I proceeded without it.

4. Put the phone in downloading mode.

5. Started Odin.

6. selected new ops, spica_jc3.ops.

7. I downloaded and used i570EXXJD1 firmware from http://samsung-firmware.webs.com/. Earlier when I was trying to use latest firmware for asia, i.e., I570EDXJC4, it was not working.

8. Of note, i did not use debug mode.

Now, I have Android 2.1 with 130 mb of internal memory!

Unknown said...

Hi Sameer, I just flashed to JD1 and I wanna aply Leshak’s Lk2.02 mod. I can't understand the 2nd step from the his install guide:
1. Download '.zip' файл: LK2-02-1_update.zip
2. Put it to root of SD card! (mount or with help adb)
3. Download Kernel: i5700_LK2-02_PDA.7z
4. Flash i5700_LK2-xx_PDA by Odin as PDA file.
5. Kernel will flash and Spica reboot and enter in Recovery
Can you pls help me?

Ravi Teja J said...

@sameer -is multitouch present ? Am nt asking abt pinch to zoom, jus multitouch ,i.e. do 2 letters pressed at once register 2 letters on keyboard or jus the 1st letter ?

Ravi Teja J said...

guys anyone??

Unknown said...

please do me a favor please, i have upgraded my spica to eclair (I570EDXJC4), right now i want to downgrade it to cupcake using firmware from samsung-firmwares (I5700DXJA1 - one package tar) but it stucks on 'setup connection'. thank you.

Ritesh Gupta said...

Stroe - ADB comes with Android SDK, which provides ways to push data onto your phone. I've installed the kernel too. What you can to do is copy the file using windows onto the base of the SDCARD.

Anonymous said...

Hi Sameer,

Waiting for you to try out Samdroid Net firmware.

I tried understanding it...But the guide seems a bit tough.

Can you try the same and make a simple guide for us ... Greakies

Thanks
SGX100

Unknown said...

SUCCESS!!!

I am now tasting eclair.

many thanks sameer and all other posters.

i'm running into the 3g/gprs issue though. is there an update or fix?

I work for the wireless provider, so i know the APN by heart.....if i enter them incomplete or incorrect, they save. only when i enter them correctly and completely will they not save (and thusly not work)

Unknown said...

Thanks Sameer, finally upgraded to 2.1.. :-) Also Thanks to Ritesh for the Windows 7 guide..

Flashed in I570EXXJCF

After boot up it has an Internal memory of 126MB.. It quicker than 1.5 if window animations are disabled. Also more apps for 2.1.. :-) Camera interface has lots of additions.. Its good..

Pantheon eats lots of battery and memory, any idea how to disable it and go back to the old one without rooting it ?

I tried home++ , its good .. But anything better ?

Regards
Goutam

Ravi Teja J said...

those who got stuck at setup connection,put all the files requiredfor flashing in the odin folder before starting.if u muiss this step u may get stuck at setup connection

Ravi Teja J said...

and jd4 is excellent..just installed it..even with pantheon it is really fast when compared to other firmwares:)

chanshri said...

Hi Sameer, Before i really could put my efforts to try your inputs, the official update came in, enjoyed your bloggs anyway, learnt a lot

ravisghosh said...

@john:

Could you please help me out with manual gprs settings for bsnl karnataka? As usual, bsnl call center is of no use!

Unknown said...

@ Ravi S Ghosh I only know the settings for Rogers Wireless here in Canada.

And I did some hunting on the internet and I found what appears to be a fix for the 3G/GPRS issue that has been noted.

I must credit INTREPID-NY on Android Forums with pointing me in the right direction....it was for another problem, but i used the basic idea to get me the rest of the way.

Before starting you must have a MicroSD card installed. You MUST have Windows configured to show extensions of known file types! Do not proceed until you're sure you can see extensions of files. See here for simple instructions on how to show extensions in Windows: http://www.tacktech.com/display.cfm?ttid=193

******I make no guarantees that this will function for anyone. Please consult your carrier for your specific APN settings******
1. Install APN Backup & Restore (free).
2. Reset device (battery pull)
3. Open APN Backup & Restore & select Backup (even if you don't have any APN saved)
4. Plug phone (or SD card) into computer and open file in Notepad (or any XML editor) - File will be found in a folder called ApnBackupRestore
5. Enter APN settings manually *example below then Save file
6. Unmount phone or place SD card back in phone
7. Run APN Backup again and click Restore. Select the file to restore. When prompted to search for all instances, answer: NO
8. Reset device (battery pull)

One the phone has restarted, you should see the APN saved.

When open in notepad, scroll al the way to the bottom. You should see a few basic settings, but you will need to fill in the blanks.
*I was running into a problem where the APN wouldn't save after changing the MNC from 72 default to the carrier required 720. An apparant fix is by changing mnc="72" to mnc="720"

Before:






After:






Rogers Wireless APN settings:

name: Rogers
apn: rogers-core-appl1.apn
proxy:
port:
username:
password:
sever:
mmsc: http://mms.gprs.rogers.com
mms proxy: 10.128.1.69
mms port: 80
mcc: 302
mnc: 720
apn type: internet + mms
auth type: none

My best wishes with your attempts to get 3G/GPRS, and even MMS up and running.

Anonymous said...

Hi Chanshri,

Where did you find the official update

Karl Francisco Fernandes said...

@chanshri : How did you get the official update? Did you give it to the Samsung service center? If so, where?

Niranjan Patil said...

Hi Guys, Samsung now has official firmware i570EDDJC5 (Released 23 April 2010, Indian version) with them. The service centers use exactly same method listed here to update our phones. Only difference is that they are responsible if its bricked!

Now get to your Samsung support center in your city and get it updated. The operators or executives wouldn't be aware and might not help. Talk to an engineer there, and just tell him you need to update your i5700's firmware and check the version he has with its date. If its older, ask him to download the newest one for i5700. It takes just 5 minutes for the job. You might need proof of purchase probably.

As of me, I went with XXJD4 2.1update1 and should agree with others, this is much better than DDJB2.

Anonymous said...

@aman @teja
hey dudes did u guys got ur official update yet done . do inform us we are waiting for lovely eclair .. i too from INDIA chennai

Anonymous said...

THE OFFICCIAL UPDATE TO 2.1 AVAILABLE IN SAMSUNG SERVICE STATION in chennai , india ... I JUST GOT IT DONE NO ISUUES .. KEYPAD RESPONSE IS VERY GOOD AND FAST .. NOW SWIPE OPTION FOR PHOTOS . SLIDE TO LOCK , CAMERA ZOOM ,,, AUTOMATIC SETTING FOR GPRS,,,, FILE MANAGER BUILT IN ,,, BLUETOOTH WORKING ,, GPRS STABLE ,,,AND WHOLE NEW INTERFACE ,,,TAKES 1.5HRS TO BE DONE ... TAKE XEROX OF UR BILL FOR SUBMISSION ... LOVE ECLAIRS .. LACKING IS SUPPORT FOR OFFICE FILES AND PDF ...documents to go is good software for that

Unknown said...

Hi Sameer,

I have tried to install Live Wall Paper via market and it got installed also but m wondering as I am not able to make it work !! Although live wall papers got installed but none of them are working !!!

Is it same case with your upgrade ??
Is live paper working in your phone?

Pls let me know if there is any procedure to make it enable.

Regards,

Riyaz

Unknown said...

Hi Sameer,

I have tried to install Live Wall Paper via market and it got installed also but m wondering as I am not able to make it work !! Although live wall papers got installed but none of them are working !!!

Is it same case with your upgrade ??
Is live paper working in your phone?

Pls let me know if there is any procedure to make it enable.

Regards,

Riyaz

Nipun said...

@ Sameer
i bought this phone on Sunday and yesterday updated it to 2.1 with your guide
but i m having the problem of 0.00 mb
i updated DXJC4
i also did it with debug only check box but id did not move with that, stuck at <1>

suggest if you can

i am thinking of going to service center because people are saying official upgrade is available (i am from Delhi), but when they see 2.1 already they may take it as warranty void.
what you suggest, if you say re-flashing then with which firmware and what options selected
waiting.....

Anonymous said...

@nipun
factory reset it i think it will roll back the flassh .. and yes 2.1 is available now at samsung free of cost and hassle free . no need to try flaash simply call samsung cust care at 3030 8282*, 1800 110011**, 1800 3000 8282, 18002668282
Monday – Sunday : 9.00 AM - 8.00 PM(IST)
*add ur std code

Ritesh Gupta said...

hi Nipun,

I had the same problem. This should save you time, copied it from my guide:

I570EDXJC4 - single package. Worked cool, but no matter what options I try - gave 0.00 B internal storage.
I570EDDJB2, I5700DXJB3 - Multi package, installed fine.
i5700EXXJD1 - Currently running this one, but not able to load contacts from Sim.

Everything running cool now. No issues that I know of. Trying to get some other cool stuff to work.

-Ritesh

GREAKY said...

@ riyaz - live wall papers did not work for me either...

@ Nipun - I think you can take your chances and take the phone to the service center for the official upgrade.

Ravi Teja J said...

hi,i am on jd4 .i dont have an option to format the memory card.
there is an option "format sd card"but it cannot be clicked..
.is it normal??

Ravi Teja J said...

just read at http://www.samsungfirmwareworld.com/jd4-can-t-format-sd-card-t179.html
that the problem is present in the firmware..tried with different capacity memory cards and unable to format them..

Unknown said...

hey master could u have any proble m solution for imei=0*15 after falshing with "efs clear" option ...pls help dear.

mail me solution at "jay9331007@gmail.com".


pls that is a big problem pls pls publish its solution as quick as quick.
we'r waiting..pls reply

Ravi Teja J said...

@sameer do u get poor touch screen response when you connect the phone to pc via usb?? i 'm having this problem when connected,i press a icon but menu or notification window or something else opens..when connected to charger this problem is not there..i dnt knw if it is recent or from the beginning, observrd it recently...
does anyone else notice this or is it just me:(

Nipun said...

@ Sameer and Ritesh
hey thanks guys for help
yesterday night i reflashed it with the latest XXJD4 firmware which is latest European firmware I think
it gave me 130 mb free and also running with no lags at all (i used debug)

thanks Sameer for this guide

@ Sameer and other Androians

can u suggest some "must be" applications which i can download to make my eclairs more chocolaty

viky said...

Did somebody tried mods available at samdroid, does they improve performance or experiance. I am running JD1. I want to try those but confused will flashing the modes means rooting ??

GREAKY said...

@ nipun - I had posted my list here : http://www.greaky.com/2010/04/must-have-android-apps.html#links

Nimesh Abraham said...

@nipun,
Where did u get JD4?.Pls send me that link.

Ravi Teja J said...

went today to a samsung service centre (at dilsukhnagar,hyderabad)..the guys there had no idea about android..i spent some 20 mins to explain them about the whole android 2.1 update and only then he checked his system for an update..he finally said he ll download the files and told me to come tomorrow..
Service centres are now using ODIN 4.16

Unknown said...

@ Nimesh

You can find any of the firmware from following link.

http://samsung-firmware.webs.com/apps/auth/login?why=pw&try=1&wp=1&next=WEBPROTECT-samsungandroidi5700.htm

Just sign in free and you can download any of the firmware.

Regards,

Riyaz

Unknown said...

Hi Sameer,

I manage to get Live WallPaper working on my spica without Rooting.

But the problem is it is only working on Lock Screen, when I do unlock its not working on home or other screen !!!

Any idea how to get it working on all screen ??

Regards,

Riyaz

Sunil Lekhwani said...

hi riyaz, how did u do live wallpaper

Sunil Lekhwani said...

dear sameer I saw a lot of guys clamouring for European firmwares. on a forum somewhere, may be on samdroid, I came across the clarification . after installation of euro firmware there is less space for application memory. because samsung gave more space to firmware. that is why they function smoothly. but that comes at the cost of a about 30 mb memory less for applications. with this point in mind Indian 2.1 firmwares are better albeit with a very slight lag.

Anonymous said...

dear sameer
thank for the guide.... its perfect...
i have one problem am not able to download anything from android market even after having 130 mb of free internal storage... please help...

Unknown said...

Hi sameer,

I ha e got an official update of eclair. But since then my internal memory has come down
Now its 130mb without any apps in it. I contacted th service centre but they told the memory will come down.. can you please help me in getting me on getting my memory back. Else is there any chance of going back to 1.5 version . Thanks a lot in advance

Tesla said...

Hi,
I have upgraded my samsung spica to 2.1 here in hyderabad,just curious to know what are the differences in the version of eclair that samsung provides in india with that of european countries?

Unknown said...

Hi sameer,

I ha e got an official update of eclair. But since then my internal memory has come down
Now its 130mb without any apps in it. I contacted th service centre but they told the memory will come down.. can you please help me in getting me on getting my memory back. Else is there any chance of going back to 1.5 version . Thanks a lot in advance

Nimesh Abraham said...

@ sameer,
I hav approached the SAMSUNG SERVICE CENTRE at Kottayam,KERALA,but they were not able to do the flashing(they tried for 2 days).Then i hav flashed myself with your guide, Thanks for your flashing guide.First i flashed my SPICA to DDJB2, but it's little slow and some other issues,GPS and 3G not working.Later i have flashed to the latest Europian firmware XXJD4.I didn’t checked the debug option.Everything working smoothly and its very fast (3G and GPS WORKING)compared to DDJB2.So i request you to update your guide with XXJD4.MUSIC CLARITY IS EXCELLENT IN ECLAIR and IT HAS AN EQUALISER TOO.

RajaTT (Theraja) said...

Hi Sameer,
What is NPC?
Where is it?
(Please do not laugh)
Really I dont see anything like that and how do I disable it.
TT Raja

Unknown said...

@ Sunil & All ( Hope Sameer dont mind my replies & Suggestions)

If you want to get Live wallpaper working on your phone without rooting here is the procedure.

1) First download any livewallpaper from android market on your phone ( it will not work but dont worry )

2) Then download Android PC Suit from below.

www.pandapp.com

3) Install and run the program.

4) When program start on top left side corner click on phone icon and choose language as English ( As by default program starts in chinese language)

5) Download live wallpaper picker ( Pls google you will find link ) or use link below.

www.4shared.com/dir/2186128/3d16200/sharing.html

6) Put your phone in debug mode
Setting > Application > Development and choose debug mode.

7) Now connect your phone to your PC/Laptop and when it shows debug mode connected on your phone click on refresh icon in Android PC suit hear phone icon.

8) It will detect your phone and will ask to install Panda Deamon in your phone... click next and let it install in your phone.

9) After installation your phone name will display in the menu.

10) Now click on Apps on left hand side, it will open another window displaying all apps installed on your phone.

11) Click on Add buttong on top left side, browse the path of Live WallPaperpicker file and click on install.

12) It will install Live WallPaper Picker on your phone.

Thats it, now you have Live WallPaper picker on your phone and you can install & choose wall papers you want to use.

Enjoy..

@Zubin & All,

All European firmware are designed to use more space to make your phone work faster hence Internal Memory remains to 130MB only.

If you need more memory you can flash to i570EDDJB2 (Indian Firmware guide by Sameer).

@ Nimesh,

Sameers guide is basic procedure, any one can you to flash there phone with the firmware available on net.

@ Raja,

NPC is New PC suit by Samsung to control your phones contacts, sms and other stuffs.

Why do u want to disable it ?

Regards,

Riyaz

Unknown said...
This comment has been removed by a blog administrator.
Unknown said...

Hi, I just tried following your instructions exactly as you wrote them. After pressing start, I just get this:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0

And absolutely nothing happens. Any idea why? :)

GREAKY said...

@ Riyaz - I don't mind your answers at all.. its a help after all.

@ Tom - two things could be causing that. Drivers or the OS .. you should try reinstalling the drivers but before that ensure that you are using WinXP.

Ajay Jain said...

Offical 2.1 update in Delhi.


Here is the address of one of the ASC, in delhi where you can get firmware/OS android 2.1 updated for samsung galaxy spica i5700 for free of cost:

Customer service plaza
Cc-28, Kalkaji,Nehru Enclave,New Delhi
PHONE NO- 011 40641234 (they pick phone hardly)

Ajay Jain said...

Offical 2.1 update in Delhi.


Here is the address of one of the ASC, in delhi where you can get firmware/OS android 2.1 updated for samsung galaxy spica i5700 for free of cost:

Customer service plaza
Cc-28, Kalkaji,Nehru Enclave,New Delhi
PHONE NO- 011 40641234 (they pick phone hardly)

RajaTT (Theraja) said...

@ Riyaz. Thanks. Butr some one advised to disable it before flashing.
I tried few times and almost bricked the spia. ( I gues so)
It stops at for hours.
<1> setup connection...
When I unplug and remove battery, the
Mobile - Exclamation - PC
message appears and that is the end. Phone does not work afterwards.
How to de-brick it? Any help?
TT Raja

Sharath Chandrashekhara said...

Hi Sameer,
First of all, thank you for your efforts to grow a community of Android users in India.
I got my phone upgraded to 2.1 in the Samsung service centre in Bangalore, BTM layout. The firmware version is i570EDDJC5.
After the upgrade my battery life has degraded majorly. From 2 days in 1.5 to just 1 day in 2.1. Yesterday night there was about 30% battery remaining and the phone had switched off by the time I woke up! Wi-Fi, Bluetooth and GPS were all disabled. I also installed Helix and killed Pantheon as I read somewhere that Pantheon consumes too much of cpu cycles.
Is there anything I can do to get my battery life up? Would rooting the phone help? or should I go to the service centre to get my battery checked?
Any help is appreciated. Thanks in advance :-)

RajaTT (Theraja) said...

Hi Riyaz and Sameer,
Finally I upgraded just now.
I am happy.
I id not select CSC (Or scs) files. And it worked.
But I am unable to set the ringtone. It always shows silent and I am unable to change it. I am trying. Some one can help on this.
Thanks to all.
TT Raja

Ritesh Gupta said...

I don't think its bricked bro. Try this:

I thought I had bricked it once, when it wouldnt start - and threw a triangle warning symbol when trying to boot up. I was stuck at this for about 1 whole day. The phone was no longer allowing any other firmware load:

- All I did to get it corrected was install Kies and connect the phone to the system in download mode. Kies tries to identify the device and fixes something in the proces. By the time Kies comes up with the screen telling you about whether an update is needed or not for your device, the device is already fixed. At this moment, you can unplug the device, and its ready for another flash after a reboot.

Ritesh Gupta said...

@Sharath - My battery life has also gone down. The number of widgets you use also decides the run time of the battery.

What I do to save battery is kill everything (including pantheon) when phone is not in use. Download a widget like ES Task Kill. This will kill all the processes currently running.

When you are ready to use the phone again, just press the home button and everything loads up.

RajaTT (Theraja) said...

Hi all,
Thanks.
I have upgraded. but few things are not working.
1. Internet
2. 3G is not identified.
3. Ring tone is set permenantly silent mode. Unable to change.
May be few more problems may be there.
How do I correct these.
Thanks in advance.
TT Raja

RajaTT (Theraja) said...

Hi Sameer,
In the device manager window, I do niot see Samsung Android modem and Samsung USB device.
Could this be the problem with my phone?
TT Raja

Unknown said...

Hi Sameer,

i'm on XXJE1 now its works perfectly fine, earlier i was on XXJD4, however i'm struggling with GPS, it was not working then & it isn't working now.

Please help...

Thanks in advance,
Mayuresh

Dan Leedham said...

Anyway that Mac users can do this?

Unknown said...

sameer, i was trying to install the 2.1 but it wasn't able to installing the android 2.1 and then i had to take out the battery but when i turn the phone back on again it doesn't book anymore but shows cell sign and computer. Is there anyway I am able to do anything from this point? thank you.

Unknown said...

no luck to install 2.1 and instead my phone now shows cell phone symbol with computer symbol and it doesn't boot up to anything now. How am I able to refresh everything so it will work?

Unknown said...

@ TOM,

This is just a problem of com driver, or your phone is not getting detect as serial device.

Try to reboot your PC, then put your mobile in download mode and retry to Flash.

@ RAJA,

Exclamation mark while boot means your Bootloder and firmware did not match.

Which firmware did u tried to flash?

No ringtone means you have not selected CSC file. Choose CSC file and flash again it will solve your problem.

Alternatively you can download ringtone from market and use as ringtone, but this way u will not have default ringtones.

@ Sharath

Install Advance Task Killer and you will see how many un wanted tasks are running, kill the ones which you dont need.

It will help to increase battery life.

Rooting wont help for battery life!!

@ RAJA,

Reflash with CSC file and proper firmware files it will solve all your problems of Internet, 3G & Ringtone.

CSC file contains Cache files which requires for proper function of all these.

Also device manager will not show ur mobile as Samsung Mobile when it boots normally.

It will show only in download mode.

Regards,

Riyaz

RajaTT (Theraja) said...

Hi Riyaz, Sameer
Thanks.
You r right. The CSC files are neede but it was not geting installed due to what ever reason. I could not make out. Finally I went to Samsung Service in Chennai. I had to go to three centers before locating the right place. Samsung engineers are also not well informed on this matter excepting one or two.
It was flashed again They installed a different version no though. ( i5700EDDJC5)
All ended well and the thing is working. It is really nice and I like it.
Thanks to all guys for the support and info.
TT Raja

RajaTT (Theraja) said...

Hi all,
I got my Spica flashed with 2.1. Phone is working with all fuctions.
But I am not bale to access thr phone SD from PC. I am unable to copy the pictures etc. from phone or vice versa.
I tried with KIES and NPS also.
Any more drivers are to be installed??
TT Raja

Unknown said...

@ RAJA TT

When u connect your phone to PC it displays connection on your phone in notification area as USB connect.

Drag the notification down and click on USB Connected menu, when it opens click on Mount and your SD Card will be displayed on your computer.

Enjoy.

Regards,

Riyaz

RajaTT (Theraja) said...

@Riyaz
Hi Riyaz, Thanks a lot. I am able to see the pics now.
TT Raja

Karl Francisco Fernandes said...

My Indian brothers and sisters,

The good folks over at Samsung Firmwares have finally uploaded our official Android 2.1 firmware I570EDDJC5. Download it here:
http://www.multiupload.com/WZ4IC7B322

Happy modding everyone! Special thank you to Sameer once again, for this post and all the info in it...

darshan said...

hi sameer....

I am using JE1 now.... n samsung has posted Indian JC5... can u tell the difference b/w regional firmwares.... what will be the difference ... should I flash to JC5???

Ravi Teja J said...

@darshan- jc5 is very similar to jcf..but does not have few bugs of jcf..flashed ddjc5 and i dnt have any problems till now,except for slight lag in pantheon.(with helix launcher its working fine)
indian firmware specifically has a hindi keyboard and has an orkut app by default installed.other than tht everything is same
phone memory is 130 mb free after fresh install of ddjc5

Ravi Teja J said...

Everyone-just wanted to tell you that
ddjc5 firmware package seems to be missing the bootloader file for 2.1 so better to flash it on a existing 2.1 firmware.when flashed on 1.5 directly it caused errors ..so just be careful.

Karl Francisco Fernandes said...

@Ravi: So what do you suggest? Do we need to flash some European 2.1 firmware first, and then DDJC5?

Or is it possible to extract some .tar bootloader file from an European package and put in Odin "BOOT" field at the time of flashing DDJC5?

I'm a noob, so this may sound stupid...

Unknown said...

Hi All,

Internal Memory remains 166MB with JB2 where as with JC5 it remains 130MB

I prefer to be on JB2 as there isnt must difference between JB2 & JC5 also cannot afford to loose 36MB internal memory !!

I am getting same features, modding & widgets on JB2, also I manage to do rooting on JB2 & install live wall paper.

Rooting & Live Wallpaper required around 30MB which gets compenset on JB2..

M happy with JB2.

Regards,

Riyaz

Unknown said...

@ RAJA,

Good info for all users who want to upgrade from 1.5 to 2.1

Regards,

Riyaz

Unknown said...

Hi, i cannot download apps, i was not able to flash with csc, but worked fine without. everything else is working a treat, i would hate to have to go back to 1.5 to get the apps working. anybody know what i can try to rosolce this problrm or maybe even know the cause of 'download unsuccessful' everytime i try get an app?

Unknown said...

@ Karl

You can upgrade to any European firmware first then flash to JC5 it will work smooth.

Dont mix bootloder from European firmware with JC5.. your phone might go into toss!!

Regards,

Riyaz

Unknown said...

@ Karl

You can upgrade to any European firmware first then flash to JC5 it will work smooth.

Dont mix bootloder from European firmware with JC5.. your phone might go into toss!!

Regards,

Riyaz

Karl Francisco Fernandes said...

@Riyaz: Thanks for the info bro... Just wanted to know if you've already tried DDJC5. If you have, can you veryify that everything is working fine. I read some complaints on the Samdroid forum that some ringtones are missing (no ringtones, only silent) and also GPRS is not working correctly. Do you have any such problems?

Ravi Teja J said...

Gprs(tata docomo),gps are working fine on ddjc5..dnt knw why I had the ringtone issue..
Could tht be due to wrong flashng or because of bad package?

Unknown said...

@ Karl,

I havent tried DDJC5, will try on Thursday as I have holiday on Thursday & Friday and will let u know the result.

Regards,

Riyaz M Shaikh

RajaTT (Theraja) said...

@Karl,
I am using jc5.
it is working fine.
I have also installed easytether and working well.
TT Raja

RajaTT (Theraja) said...

Hi all,
Any one thought of installing Android 2.2 in i5700??
TT Raja

Unknown said...

i update using jc3, and it works...

nopolthepilot said...

Hi guys, Android 2.2 is out, so let's petition to get Samsung to update the Spica to the new OS (in case they aren't planning on updating)! The petition may not do much, but it'll be a start!

http://www.petitiononline.com/sgalax22/petition.html

islam said...

i Arabic language and key-bored are available in this update ?

Unknown said...

how do i install applications on my i5700???

Unknown said...

how to install applications on my i5700

TheGuyNextDoor said...

Spoke to Samsung India Support today evening. The update should officially be available next week in Bombay!

Unknown said...

@Halotracer:

my phone was bricked and a "phone and Computer" sign was appering.. it was not even going to "Download" mode...

but thanks a lot to YOU... I followed what you say now i am on 2.1 enjoyment...

Thanks a lot... you r a life saver ;)

Anonymous said...

@guy next door
u mean the official update from eclair 2.1 to froyo 2.2 will be available . thats great i am thrilled as 2.1 has made the phone a bit of slow .. i will be calling the samsung customer care and will let u knoow

Unknown said...

@ GAURAV

You can install apps from Market in your mobile..

Just connect to internet, signin to your gmail account and then you will be able to install apps from Market place.

Regards,

Riyaz

Unknown said...

@ GAURAV

You can install apps from Market in your mobile..

Just connect to internet, signin to your gmail account and then you will be able to install apps from Market place.

Regards,

Riyaz

Unknown said...

but den d market icon is not der in my phone... wil installing android 2.1 install d market application on my phone???

Unknown said...

finally finished flashing my i5700 spica to Android 2.1 i570exxjd1 .. its works like a charm now .. speed is gud. No APN etc issues for me

only 2 issues m facing is

1) No live wallpapers
2) m unable too add FACEBOOK account (in SYNC option)

Can anyone tell me any better firmware ver than i570exxjd1

FrEaK said...

Hey Sameer,
Ive rooted my Spica using LKMOd and then applied the Samdroid 1.03 MOD.
Phone keeps crashing a lot of times, and dusnt reboot.
Is it safe for me to flash the original Eclair firmware once again?
Is it safe? Or should I wipe Data/Cache using the recovery mode and then try it. Im very confused. Plz Advice.
Thnx A Gazillion!

GREAKY said...

Freak - you should be ok to flash any other firmware.

Unknown said...

@GAURAV

Gaurav u r on which firmware?

Yes if you flash to 2.1 DDJB2 or DDJC5 Market place will be there in your phone.

@ SURAJ

You will need to do Rooting and install Live WallPaper Picker to enable live wall papers.


Face book works fine in DDJB2 or DDJC5 you may try to flash one of them.

@FREAK

Which firmware you flashed first ?
Reflash will solve your problem. Dont do LKMOD again.


Regards,

Riyaz

The. Commenter said...

Any one, can you please help me how to solve APN issues, unable to do browsing, os behaving like mental disorder. pls help me bcos browsing highly required during my work. I had flashed with ddjc5 rom to 2.1.

darshan said...

has anybody tried JIT7.1 compiler on spica phone boosts with speed but still crashes

harpreet chhatwal said...

hey sameer..

i m in india and currently on JC1 firmware..though pretty stable but has APN issues(that is ..it connects to the GPRS but doesnt transfer any data..)...

can you please recommend me some better firmware..something probably more stable and without these APN issues..

how about the officially launched firmware in india...how efficient is that firmware..what is it btw?

regards..
harpreet

Unknown said...

how to flash to DDJB2 or DDJC5?
my phone says i5700jxil2 n build number cupcake.jpil3

Anonymous said...

@harpreet
i have been using the official firmware "eclair.ddjc5 2.1- update 1"... its preety good ... no issues .. yeah one is the background application runs like video player as shown by my task killer .. its very stable and haasnt crashed till now .. its available in samsung service station .... call them at *30308282 and 180030008282 dont forget to add *std code

Unknown said...

@GAURAV

User Sameers flash guide to flash your phone to DDJB2 or DDJC5.

Regards,

Riyaz

Sunil Lekhwani said...

I am using spica with 2.1.
Some say its price has gone up to 14500 and i7500 is coming for 11500. So considering some features like:
I7500
HSDPA 7.2Mbps / HSUPA 5.76Mbps
5 MP Camera with Auto Focus & LED Flash
8 gb internal memory- for unlimited appa is it worth thinking again of.

Vikas Bhat said...

Hey, I'm trying to upgrade but what the heck, I can't get in to Download mode at all! I tried exactly the same way - Volume down + Camera + Power button. Just camera ringer and power menu pops out! No one seems to be having problems in getting into download mode!! sigh....

Vikas Bhat said...

I cant even get into download mode..what the heck! did exactly the same Volume down+camera+power button held together...nothing happens....

Unknown said...

@ Technology at its best!

Have you switched off your mobile before attempting to put yout mobile into Download mode ??

Regards,

Vikas Bhat said...

Thanks Riyaz, I tried flashing. Something went bad.
I did a hard reset, made sure no Samsung PC software was running, I put the phone in download mode, Odin detected it on Com(5). Selected the right files and hit the Start button. It was stuck at <1> setup connection... for a long time (12 minutes). Sometimes Odin software was crashing.. Now I see that the Phone is not booting but shows a funny Mobile to PC picture and stays there. How do I go back? or Should I just go to Service center? Help is most appreciated... is there any way I can hard reset and go back to 1.5?

Vikas Bhat said...

I had issues in flashing the 2.1 ROM. Odin downloaded just crashes the moment I press Start button. Says it performed an illegal operation n exits.

Did anyone face this issue? I tried 10 times, removing battery, switching it off n various things. Just can't make Odin run...

Unknown said...

@ TECHNOLOGY

Which firmware you tried to upgrade to ?? DDJB2 or DDJC5 ??

Keep in mind DDJB2 required old spica file where as DDJC5 requires new spica file.

PDA file in DDJC5 does not contain file to upgrade 1.5 to 2.1!

It looks u tried to upgrade 1.5 to 2.1 with DDJC5 directly ??

You will have to upgrade your 1.5 to DDJB2 first then again upgrade to DDJC5 to make it workable.

Dont worry about funny pc to mobile picture on your mobile. Just put it in download mode again, dont run any Samsung software.

Make Odin run first, chose Spica, Boot, PHONE, PDA, CSC files to flash. All should go normal.

Dont wait for long time if u get stuck at <1> setup connection.. it will not do anything for long.

Also make sure you have correct files downloded and you are using correct Spica file.

Regards,

Riyaz

Unknown said...

@ TECHNOLOGY

Which firmware you tried to upgrade to ?? DDJB2 or DDJC5 ??

Keep in mind DDJB2 required old spica file where as DDJC5 requires new spica file.

PDA file in DDJC5 does not contain file to upgrade 1.5 to 2.1!

It looks u tried to upgrade 1.5 to 2.1 with DDJC5 directly ??

You will have to upgrade your 1.5 to DDJB2 first then again upgrade to DDJC5 to make it workable.

Dont worry about funny pc to mobile picture on your mobile. Just put it in download mode again, dont run any Samsung software.

Make Odin run first, chose Spica, Boot, PHONE, PDA, CSC files to flash. All should go normal.

Dont wait for long time if u get stuck at <1> setup connection.. it will not do anything for long.

Also make sure you have correct files downloded and you are using correct Spica file.

Regards,

Riyaz

Unknown said...

@ TECHNOLOGY

Which OS u r using on your PC?

Regards,

Riyaz

Shivoham said...

Thanks a bunch Sameer for the very useful guide.

Upgraded with i570EDDJC5 with One Package option.

If you get stuck at 'Setup Connection' refer to comment by jiahong on march 01 for resolution.

Vikas Bhat said...

Ok, I ungraded, I downloaded a fresh copy of Odin from a Samsung forum and it worked fine. Thanks to this blog n riyaz.

Unknown said...

@ TECHNOLOGY

Its good to know u got upgraded..

Its look my yesterday's post for your solution did not got posted!! i wrote complete solution for your problem.. anyways u already on 2.1 now,,, enjoy.

Regards,

Riyaz

jak :( said...

sorry probably a stupid question
Does remove sim lock refer to a PIN code or as to whether the phone is locked to a particular network?

Unknown said...

@ JAK

SIM lock refer to a PIN code lock.

@ HANS

Just remove ur battry from phone for a while, reinsert, put ur mobile in Download mode and flash with earlier firmware.

Plug in your mobile to PC when u selected all files in ODIN. It should appear in ODIN as COM5 or so.. dont bother its getting appear in windows!!!.

Dont use Samdroid kitchen its not ment to work with I570EXXJE1!!

Regards,

Riyaz

Unknown said...

@ JAK

SIM lock refer to a PIN code lock.

@ HANS

Just remove ur battry from phone for a while, reinsert, put ur mobile in Download mode and flash with earlier firmware.

Plug in your mobile to PC when u selected all files in ODIN. It should appear in ODIN as COM5 or so.. dont bother its getting appear in windows!!!.

Dont use Samdroid kitchen its not ment to work with I570EXXJE1!!

Regards,

Riyaz

Nawaz said...

hi frns! Plz update or mail me, frm where to download I570EDDJB2 or I570XXJCE.tar. As i have all the application except this tar file to load my fone with android 2.1- Emai: nawazahmedn@gmail.com.

Jjunju Karim said...

hi jst wana knw wat happens wen the start button is pressed bse i did place it but avent seen any change 4 1hr30 i only see set up connection

Jjunju Karim said...

hi jst wana knw wat happens wen the start button is pressed bse i did place it but avent seen any change 4 1hr30 i only see set up connectiona

Unknown said...

Hi, thanks for this guide, it took a while but it worked! however i now dont have the appmarket, aby idea how to get this back?
thanks

«Oldest ‹Older   601 – 800 of 930   Newer› Newest»